Home » Products » Sequencer » Sequenced Output Power Conditioner (8 Relay +1)

Products

Sequenced Output Power Conditioner (8 Relay +1)

PWR-DA09C/P

product

The ABtUS PWR-DA09C/P is a safe and convenient Sequenced Output Power Conditioner distribution unit offering protection to all valuable rack-mounted equipments. Sequenced power up of a complete power audio system from just a push of a switch that eliminates the loud “POP” sound which may damage speakers and other equipments connected. The PWR-DA09C/P features sequenced power start up. During start up, each outlet is turned on one at a time with a delay time (Valiable and programmable) between each other. This delay prevents the “POP” sound by allowing each piece of equipment to properly power up before allowing the audio signals to pass through. The PWR-DA09C/P also features an EMI fi lter which suppresses RF(Radio frequency) and other AC line noises, ensuring a quieter operation operation of units that’ 92s plugged in. The Line Voltage sensor monitors the incoming voltage from 185~265VAC, assuring the AC voltage is in a safe operating range for the connected equipment. Its 12VDC BNC outlet also allows power for a LED light/Lamp that provides a cool-running light source for all equipment in your rack.

• Multi-Stage surge protection
• Linear Filtering Technology
• Front panel power status LEDs
• External I/O allow remote operation
• 8 switched outlets (rear) and one pass through un-switched outlet (front)
• 12VDC supply (BNC) allow any gooseneck lamp or LEDs that provides a cool running source for the rack.
Max current rating : 10 AMP (2400 Watts at 240 VAC)
Input voltage : 185 to 275 VAC without damage
Delay intervals : Total elapsed ON delay time adjustable from 1-60 seconds,
with RS-232 for precise timing and sequence order
On sequence : Respective relay goes ON base on programmed sequence/order and delay time for each relay
Remote switch: : Screw type terminal block, LED, Switch and GND
Spike protection modes : Line to neutral, zero ground leakage
Spike clamping voltage : 188 Vpk @ 3,000 amps, (133 VAC RMS)
Response time : 1 nanosecond
Maximum surge current : 6,500 amps
Relay rating : 30Amps @ 240VAC
Power consumption : 4.5 Watts (standby), 14 Watts (all realy ON)
Over voltage shut down : 185V ±1% (Low), 265 ±1% (High)
Operational : 220/240V
Housing : Metal Enclose
Dimension : 430 × 240 × 45 mm  
Weight : 3.6 kg


PWR-DA09C/P
Sequenced Output Power Conditioner (8 Relay +1)

The ABtUS PWR-DA09C/P is a safe and convenient Sequenced Output Power Conditioner distribution unit offering protection to all valuable rack-mounted equipments. Sequenced power up of a complete power audio system from just a push of a switch that eliminates the loud “POP” sound which may damage speakers and other equipments connected. The PWR-DA09C/P features sequenced power start up. During start up, each outlet is turned on one at a time with a delay time (Valiable and programmable) between each other. This delay prevents the “POP” sound by allowing each piece of equipment to properly power up before allowing the audio signals to pass through. The PWR-DA09C/P also features an EMI fi lter which suppresses RF(Radio frequency) and other AC line noises, ensuring a quieter operation operation of units that’ 92s plugged in. The Line Voltage sensor monitors the incoming voltage from 185~265VAC, assuring the AC voltage is in a safe operating range for the connected equipment. Its 12VDC BNC outlet also allows power for a LED light/Lamp that provides a cool-running light source for all equipment in your rack.
Features
• Multi-Stage surge protection
• Linear Filtering Technology
• Front panel power status LEDs
• External I/O allow remote operation
• 8 switched outlets (rear) and one pass through un-switched outlet (front)
• 12VDC supply (BNC) allow any gooseneck lamp or LEDs that provides a cool running source for the rack.
Technical Spec
Max current rating : 10 AMP (2400 Watts at 240 VAC)
Input voltage : 185 to 275 VAC without damage
Delay intervals : Total elapsed ON delay time adjustable from 1-60 seconds,
with RS-232 for precise timing and sequence order
On sequence : Respective relay goes ON base on programmed sequence/order and delay time for each relay
Remote switch: : Screw type terminal block, LED, Switch and GND
Spike protection modes : Line to neutral, zero ground leakage
Spike clamping voltage : 188 Vpk @ 3,000 amps, (133 VAC RMS)
Response time : 1 nanosecond
Maximum surge current : 6,500 amps
Relay rating : 30Amps @ 240VAC
Power consumption : 4.5 Watts (standby), 14 Watts (all realy ON)
Over voltage shut down : 185V ±1% (Low), 265 ±1% (High)
Operational : 220/240V
Housing : Metal Enclose
Dimension : 430 × 240 × 45 mm  
Weight : 3.6 kg
Download

PWRDA09C-RS232.zip

UM_PWR-DA09C(P_PWR-DA09C(PG_2022-09Sep-14.pdf
Diagram

print Print this product Enquiry Form